We manufacture racking at Bahadurgarh and send it north by road. A Fabric Storage Rack is a column with projecting arms and no front upright, so long material can be loaded along its length. Arms and decks sized for rolls and bolts rather than boxes. Most of what we send to Jammu And Kashmir goes into the pharmaceutical and food units around Jammu, Samba and Kathua, and horticulture further north.
What decides the specification in Jammu And Kashmir
Two quite different specifications apply depending on which side of that split you are on: controlled-temperature storage, or ordinary dry goods. For Fabric Storage Rack the figure that settles it is the load on one arm and the overhang beyond the last one.
Industry in Jammu And Kashmir runs to the pharmaceutical and food units around Jammu, Samba and Kathua, and horticulture further north, and that is the stock these bays usually hold.
Fabric Storage Rack — what we build to
Load per arm: Up to 1000 kg
Column height: 15 ft to 20 ft (4500–6000 mm)
Arm length: 600 mm to 1000 mm
Levels: Typically 4, adjustable
Where Fabric Storage Rack is used in Jammu And Kashmir
Across the trade it goes into steel stockists, timber and board merchants, pipe and section stores, and roll or fabric storage. The job it does is long loads such as pipe, tube, timber, profile and sheet. In Jammu And Kashmir specifically, the enquiries come mostly from the pharmaceutical and food units around Jammu, Samba and Kathua, and horticulture further north, so that is the stock we are usually sizing for.
Buying one rather than another
Anything that will not sit on a pallet without hanging over the edge belongs on cantilever rather than beams. Arm pitch is set by how much the material sags between supports, so tell us what it is made of.
Getting a price for Samba
Send the longest and heaviest item, how it is lifted, and whether you need one side or both. Tell us whether you want supply only or supply with fitting, and we will quote it that way. Everything is made at our own plant at HSIIDC Bahadurgarh — we are the manufacturer, not a stockist re-badging someone else’s frames.
Two quite different specifications apply depending on which side of that split you are on: controlled-temperature storage, or ordinary dry goods. If that is not obvious from the site, send a photograph of the bay and the dimensions, and we will mark up what will fit before anything is quoted for Samba.
Specifications — Fabric Storage Rack
Fabric Storage Rack are built on our
Cantilever Racks range, so the figures below are that
range's standard sizes.
Spanco manufactures to order, so these are what is
produced at the Bahadurgarh plant rather than a fixed catalogue size.
Final bay loading is confirmed against your pallet weight, bay width and
level configuration before drawings are issued.
Built to the ranges listed below — sizes are made to your bay.
Standard manufacturing ranges for Cantilever Racks
Column height
15 ft to 20 ft (4500–6000 mm)
Arm length
600 mm to 1000 mm
Load per arm
Up to 1000 kg
Levels
Typically 4, adjustable
Configuration
Single-sided or double-sided
Material
Mild steel
Finish
Powder coated
Configuration options
Arm end stops
Inclined arms for pipe and tube
Base-plate floor fixing
Timber or steel arm facing
Questions buyers ask before ordering
What are Fabric Storage Racks used for?
Fabric Storage Racks hold long or awkward material that will not sit on a pallet - pipe, tube, bar, angle sections, timber, boards and sheet. With no front upright in the way, material loads along the full bay length. We build up to 1000 kg per arm, arms 600 to 1000 mm, columns 15 ft to 20 ft.
What is cantilever racking used for?
Anything long that will not sit sensibly on a pallet: pipe, tube, bar, angle sections, timber, boards and sheet. Because there is no front upright in the way, material can be loaded along the full length of the bay.
How much weight can each arm carry?
Up to 1000 kg per arm in our standard build, with arm lengths from 600 mm to 1000 mm and columns from 15 ft to 20 ft. The load must be spread across arms rather than concentrated at the arm tip, which is where most overloading happens in practice.
Top Racks Manufacturers in Samba — Delivering Quality
Steps of manufacture
How we work
Every rack on this site is made on one line at our own
5000 m² plant in Bahadurgarh.
Nothing is bought in and re-badged, which is why we can answer for the
steel grade, the coating and the bay loading on the same call.
A single lorry covers several of these towns on the same run, so ordering alongside a neighbouring site usually shortens the wait across Jammu And Kashmir.